 |
[#35025] pcDuino Cortex-A8 ミニPCプラットフォーム
商品ページにジャンプ
|
 起動ログ
2013-04-23更新
<<前のFAQ
| 次のFAQ>>
|
ブート時の起動ログ(シリアル出力のモニタ)です。参考にしてください。（将来のロットでは表示が変わるかもしれません）
HELLO! BOOT0 is starting!
boot0 version : 1.5.0
dram size =1024
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00056000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[ 0.179] boot1 version : 1.5.0
[ 0.179] pmu type = 3
[ 0.180] bat vol = 0
[ 0.212] axi:ahb:apb=3:2:2
[ 0.212] set dcdc2=1400, clock=1008 successed
[ 0.214] key
[ 0.227] no key found
[ 0.227] flash init start
[ 0.596] flash init finish
[ 0.598] fs init ok
[ 0.599] fattype FAT16
[ 0.599] fs mount ok
[ 0.605] script finish
[ 0.606] power finish
[ 0.614] BootMain start
[ 0.614] 0
[ 0.629] usbdc_vol = 4000, usbdc_cur = 0
[ 0.629] usbpc_vol = 4000, usbpc_cur = 0
[ 0.632] init to usb pc
[ 0.635] set pc
[ 0.725] power_start=0x00000002
[ 0.725] pre sys mode
[ 0.725] startup status = -1
[ 0.728] key value = 0
[ 0.731] recovery key high 6, low 4
[ 0.735] unable to find fastboot_key key_max value
[ 0.743] test for multi os boot with display
[ 1.367] show pic finish
[ 1.367] load kernel start
[ 1.385] load kernel successed
[ 1.385] start address = 0x4a000000
[ 1.387] power exit detect
[
U-Boot 2011.09-rc1-svn98 (Mar 07 2013 - 15:03:53) Allwinner Technology
CPU: SUNXI Family
Board: A10-EVB
DRAM: 512 MiB
NAND: 1900 MiB
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:5-
-name- -start- -size-
bootloader : 1000000 2000000
env : 3000000 1000000
boot : 4000000 1000000
rootfs : 5000000 5dc00000
UDISK : 62c00000 14000000
-----------------------------------
no misc partition is found
Hit any key to stop autoboot: 3 2 1 0
reading evb.bin
44792 bytes read
reading uImage
6225524 bytes read
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.0.8+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6225460 Bytes = 5.9 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DRAM: 1024 MB[ 0.000000] Linux version 3.0.8+ (ubuntu@linux-server) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 PREEMPT Thu Mar 7 15:02:
13 CST 2013
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun4i
[ 0.000000] Total Detected Memory: 1024MB with 2 banks
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory Reserved(in bytes):
[ 0.000000] LCD: 0x5a000000, 0x02000000
[ 0.000000] SYS: 0x43000000, 0x00010000
[ 0.000000] G2D: 0x58000000, 0x01000000
[ 0.000000] VE : 0x44000000, 0x05000000
[ 0.000000] VE : 0x49000000, 0x01000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 245760
[ 0.000000] free_area_init_node: node 0, pgdat c0c0a110, node_mem_map c0dc9000
[ 0.000000] Normal zone: 1280 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 146176 pages, LIFO batch:31
[ 0.000000] HighMem zone: 768 pages used for memmap
[ 0.000000] HighMem zone: 97536 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243712
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/nandd init=/init loglevel=8
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 448MB 512MB = 960MB total
[ 0.000000] Memory: 829264k/829264k available, 153776k reserved, 393216K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xe8800000 - 0xf0000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe8000000 ( 640 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0505000 (5108 kB)
[ 0.000000] .text : 0xc0505000 - 0xc0bc6b10 (6919 kB)
[ 0.000000] .data : 0xc0bc8000 - 0xc0c133a0 ( 301 kB)
[ 0.000000] .bss : 0xc0c133c4 - 0xc0dc8110 (1748 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:96 nr_irqs:96 96
[ 0.000000] timer0: Periodic Mode
[ 0.000000] sw_timer_init,line:424
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] aw_clksrc_init, line:338
[ 0.000000] Console: colour dummy device 80x30
[ 0.000093] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
[ 0.040022] pid_max: default: 32768 minimum: 301
[ 0.040146] Mount-cache hash table entries: 512
[ 0.040427] CPU: Testing write buffer coherency: ok
[ 0.040601] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 0.041033] devtmpfs: initialized
[ 0.042263] print_constraints: dummy:
[ 0.042361] NET: Registered protocol family 16
[ 0.042947] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.043393] try to parse pll6 frequency from script faild!
[ 0.043433] try to parse apb frequency from script faild!
[ 0.043502] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[ 0.043559] Initialize DMAC OK
[ 0.043596] sb-pwm: sb_pwm_init 513
[ 0.043896] sb-pwm: sb_pwm_probe 345
[ 0.043917] sb-pwm: sb_pwm_probe 345
[ 0.043933] sb-pwm: sb_pwm_probe 345
[ 0.043947] sb-pwm: sb_pwm_probe 345
[ 0.043963] sb-pwm: sb_pwm_probe 345
[ 0.043977] sb-pwm: sb_pwm_probe 345
[ 0.048138] bio: create slab at 0
[ 0.048679] SCSI subsystem initialized
[ 0.048876] usbcore: registered new interface driver usbfs
[ 0.048946] usbcore: registered new interface driver hub
[ 0.049074] usbcore: registered new device driver usb
[ 0.049414] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.049716] Bluetooth: Core ver 2.16
[ 0.049761] NET: Registered protocol family 31
[ 0.049770] Bluetooth: HCI device and connection manager initialized
[ 0.049785] Bluetooth: HCI socket layer initialized
[ 0.049794] Bluetooth: L2CAP socket layer initialized
[ 0.049816] Bluetooth: SCO socket layer initialized
[ 0.050000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.050000] Init eGon pin module V2.0
[ 0.050000] Switching to clocksource aw 64bits couter
[ 0.050000] FS-Cache: Loaded
[ 0.050000] CacheFiles: Loaded
[ 0.050000] Switched to NOHz mode on CPU #0
[ 0.050000] [usb_manager]: CONFIG_USB_SW_SUN4I_USB0_OTG
[ 0.050000] [sw_hcd0]: usb host driver initialize........
[ 0.050000] [sw_hcd0]: open_usb_clock
[ 0.066422] [sw_hcd0]: host_init_state = 0
[ 0.066431] [sw_hcd0]: platform is usb host
[ 0.066495] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
[ 0.066520] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[ 0.066535] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[ 0.067049] hub 1-0:1.0: USB hub found
[ 0.067075] hub 1-0:1.0: 1 port detected
[ 0.067098] wrn: hcd is not enable, need not start hcd
[ 0.067342] [sw_hcd0]: sw_usb_host0_disable start
[ 0.067356] -------sw_hcd0_soft_disconnect---------
[ 0.067367] [sw_hcd_host0]: Set USB Power OFF
[ 0.067376] wrn: hcd is not enable, need not stop hcd
[ 0.067403] [sw_hcd0]: close_usb_clock
[ 0.067445] [sw_hcd0]: sw_usb_host0_disable end
[ 0.067480] [sw_udc]: udc_init: version 20080411
[ 0.067709] axp driver uning configuration failed(539)
[ 0.067729] axp driver uning configuration failed(551)
[ 0.067881] NET: Registered protocol family 2
[ 0.067985] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.068320] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.070427] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.071117] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.071127] TCP reno registered
[ 0.071139] UDP hash table entries: 512 (order: 1, 8192 bytes)
[ 0.071162] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[ 0.071342] NET: Registered protocol family 1
[ 0.071635] RPC: Registered named UNIX socket transport module.
[ 0.071647] RPC: Registered udp transport module.
[ 0.071654] RPC: Registered tcp transport module.
[ 0.071662] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.091616] PMU: registered new PMU device of type 0
[ 0.091683] [pm]aw_pm_init!
[ 0.108342] highmem bounce pool size: 64 pages
[ 0.108578] ashmem: initialized
[ 0.114138] VFS: Disk quotas dquot_6.5.2
[ 0.114308] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.117382] NTFS driver 2.1.30 [Flags: R/W].
[ 0.117822] fuse init (API version 7.16)
[ 0.118429] msgmni has been set to 851
[ 0.118850] cryptomgr_test used greatest stack depth: 6672 bytes left
[ 0.119250] cryptomgr_test used greatest stack depth: 6480 bytes left
[ 0.121374] cryptomgr_test used greatest stack depth: 6388 bytes left
[ 0.122399] cryptomgr_test used greatest stack depth: 6280 bytes left
[ 0.122849] alg: No test for stdrng (krng)
[ 0.123048] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.123063] io scheduler noop registered
[ 0.123071] io scheduler deadline registered
[ 0.123143] io scheduler cfq registered (default)
[ 0.123752] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.124962] serial8250.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[ 0.836277] console [ttyS0] enabled
[ 0.840496] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[ 0.847693] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A
[ 0.855400] brd: module loaded
[ 0.860524] loop: module loaded
[ 0.863675] [NAND]nand driver, init.
[ 0.867247] cmu_clk is 408
[ 0.870068] nand clk init end
[ 0.873120] offset 0xc: 0x6040
[ 0.876343] offset 0x14: 0x8200000a
[ 0.880000] [NAND] nand gpio_request
[ 0.883615] [NAND] nand driver version: 0x2 0x9
[ 0.888244] nand interrupte register ok
[ 0.892098] ret of NFC_ChangMode is 0
[ 0.895842] dma_hdle is 0
[ 0.898635] dma_hdle is 10000008
[ 0.902129] cmu_clk is 408
[ 0.904920] nand clk init end
[ 0.907962] offset 0xc: 0x6040
[ 0.911205] offset 0x14: 0x82000006
[ 0.928140] The 0 disk name = DEVICE, class name = NAND, disk start = 0, disk size = 3891200
[ 0.938464] The 1 disk name = bootloader, type = 0, class name = DISK, disk size = 65536
[ 0.946589] The 2 disk name = env, type = 0, class name = DISK, disk size = 32768
[ 0.954092] The 3 disk name = boot, type = 0, class name = DISK, disk size = 32768
[ 0.961673] The 4 disk name = rootfs, type = 0, class name = DISK, disk size = 3072000
[ 0.969582] The 5 disk name = UDISK, type = 0, class name = DISK, disk size = 655360
[ 0.977337] The 5 disk size = 655360
[ 0.980924] part total count = 6
[ 0.985273] nand: unknown partition table
[ 0.990327] nanda:
[ 0.993483] nandb: unknown partition table
[ 0.998691] nandc: unknown partition table
[ 1.108980] nandd: unknown partition table
[ 1.114255] nande: unknown partition table
[ 1.118597] benn: nand probe enter
[ 1.122083] [NAND]nand driver, ok.
[ 1.125548] sun4i gpio driver init
[ 1.129441] test_adc_init
[ 1.132374] [spi]: Found 2 spi devices in config files
[ 1.137514] boards_num modalias max_spd_hz bus_num cs mode
[ 1.145028] 0 spidev 12000000 0 0 3
[ 1.152532] 1 spidev 12000000 2 0 3
[ 1.160241] [spi-0]: cs bitmap from cfg = 0x1
[ 1.164892] [spi-0]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000
[ 1.172334] reuuimllas SoC SPI Driver loaded for Bus SPI-0 with 2 Slaves at most
[ 1.179726] [spi-0]: driver probe succeed, base e88b8000, irq 10, dma_id_rx 43, dma_id_tx 44!
[ 1.188289] [spi-2]: cs bitmap from cfg = 0x1
[ 1.192887] [spi-2]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000
[ 1.200293] reuuimllas SoC SPI Driver loaded for Bus SPI-2 with 2 Slaves at most
[ 1.207683] [spi-2]: driver probe succeed, base e88ba000, irq 12, dma_id_rx 45, dma_id_tx 46!
[ 1.216584] tun: Universal TUN/TAP device driver, 1.6
[ 1.221663] tun: (C) 1999-2004 Max Krasnyansky
[ 1.227964] wemac Ethernet Driver, V1.00 in file:drivers/net/sun4i/sun4i_wemac.c
[ 1.235557] can't get information emac_power gpio
[ 1.240307] [EMAC] ahb clk enable
[ 1.243706] [EMAC] ahb gate clk: 0x526040
[ 1.257873] wemac wemac.0: PHY SETUP, reg 0 value: 3100
[ 1.263115] emac MAC isn't valid!
[ 1.267423] wemac wemac.0: resetting device
[ 1.272338] release temp resource
[ 1.275701] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.282298] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.288705] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc0cbeef4
[ 1.296472] [sw-ehci1]: open clock
[ 1.319825] [sw-ehci1]: Set USB Power ON
[ 1.323769] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.331281] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[ 1.338410] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
[ 1.360041] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.365439] ehci_irq: port change detect
[ 1.369853] hub 2-0:1.0: USB hub found
[ 1.373651] hub 2-0:1.0: 1 port detected
[ 1.377929] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc0cbf00c
[ 1.385698] [sw-ohci1]: open clock
[ 1.409044] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.416210] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[ 1.423302] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
[ 1.484460] hub 3-0:1.0: USB hub found
[ 1.488221] hub 3-0:1.0: 1 port detected
[ 1.492470] [sw-ehci2]: probe, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc0cbf128
[ 1.500232] [sw-ehci2]: open clock
[ 1.523576] [sw-ehci2]: Set USB Power ON
[ 1.527498] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.535014] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[ 1.542155] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
[ 1.560039] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
[ 1.565436] ehci_irq: port change detect
[ 1.569752] hub 4-0:1.0: USB hub found
[ 1.573627] hub 4-0:1.0: 1 port detected
[ 1.577856] [sw-ohci2]: probe, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc0cbf240
[ 1.585641] [sw-ohci2]: open clock
[ 1.609022] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.616188] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[ 1.623275] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
[ 1.630048] ehci_irq: port change detect
[ 1.684443] hub 5-0:1.0: USB hub found
[ 1.688203] hub 5-0:1.0: 1 port detected
[ 1.692202] The port change to OHCI now!
[ 1.696371] Initializing USB Mass Storage driver...
[ 1.701438] usbcore: registered new interface driver usb-storage
[ 1.707439] USB Mass Storage support registered.
[ 1.712126] usbcore: registered new interface driver ums-alauda
[ 1.718085] usbcore: registered new interface driver ums-cypress
[ 1.724149] usbcore: registered new interface driver ums-datafab
[ 1.730233] usbcore: registered new interface driver ums_eneub6250
[ 1.736445] usbcore: registered new interface driver ums-freecom
[ 1.742508] usbcore: registered new interface driver ums-isd200
[ 1.748460] usbcore: registered new interface driver ums-jumpshot
[ 1.754609] usbcore: registered new interface driver ums-karma
[ 1.760495] usbcore: registered new interface driver ums-onetouch
[ 1.766636] usbcore: registered new interface driver ums-realtek
[ 1.772744] usbcore: registered new interface driver ums-sddr09
[ 1.778699] usbcore: registered new interface driver ums-sddr55
[ 1.784678] usbcore: registered new interface driver ums-usbat
[ 1.790678] usbcore: registered new interface driver usbserial
[ 1.796506] usbserial: USB Serial Driver core
[ 1.800918] USB Serial support registered for GSM modem (1-port)
[ 1.807105] usbcore: registered new interface driver option
[ 1.812719] option: v0.7.2:USB Driver for GSM modems
[ 1.817715] ------print_msc_config-----
[ 1.821567] vendor_id = 0x18d1
[ 1.825659] mass_storage_id = 0x1
[ 1.829489] adb_id = 0x2
[ 1.833337] usb_manufacturer_name = USB Developer
[ 1.838035] usb_product_name = Android
[ 1.842230] usb_serial_number = 20080411
[ 1.846495] msc_vendor_name = USB 2.0
[ 1.850736] msc_product_name = USB Flash Driver
[ 1.855696] msc_release = 100
[ 1.859527] luns = 1
[ 1.863218] ---------------------------
[ 1.867204] [sw_udc]: [sw_usb_udc]: binding gadget driver 'android_usb'
[ 1.873871] [sw_udc]: alloc request: ep(0xc0bf4138, ep0, 64), req(0xe7bb29c0)
[ 1.881036] WRN:L2703(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active
[ 1.889044] [sw_udc]: sw_udc_pullup, is_on = 0
[ 1.893514] WRN:L2738(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active
[ 1.902770] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.909643] android_usb gadget: Number of LUNs=1
[ 1.914300] lun0: LUN: removable file: (no medium)
[ 1.919188] lun name: lun
[ 1.922004] WRN:L2703(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active
[ 1.930078] android_usb gadget: android_usb ready
[ 1.934918] mousedev: PS/2 mouse device common for all mice
[ 1.941155] sunxi RTC version 0.1
[ 1.944703] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380239881
[ 1.951248] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 1.956040] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:8:33
[ 1.961768] using rtc device, rtc, for alarms
[ 1.965978] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[ 1.972327] i2c /dev entries driver
[ 1.975922] !!! base_Addr = 0xe88c4c00
[ 1.979764] config i2c gpio with gpio_config api
[ 1.984527] twi0, apb clock = 24000000
[ 1.989660] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[ 1.995028] usb 3-1: new full speed USB device number 2 using sw-ohci
[ 2.002656] [AXP]axp driver uning configuration failed(324)
[ 2.008287] [AXP]power_start = 0
[ 2.011562] I2C: i2c-0: AW16XX I2C adapter
[ 2.015654] **********start************
[ 2.019486] 0x40
[ 2.021443] 0xf8
[ 2.023366] 0x28
[ 2.025288] 0x0
[ 2.027124] 0x0
[ 2.028960] **********end************
[ 2.032680] !!! base_Addr = 0xe88c6000
[ 2.036551] twi1, apb clock = 24000000
[ 2.040650] I2C: i2c-1: AW16XX I2C adapter
[ 2.044743] **********start************
[ 2.048574] 0x40
[ 2.050524] 0xf8
[ 2.052447] 0x58
[ 2.054369] 0x0
[ 2.056204] 0x0
[ 2.058039] **********end************
[ 2.061756] !!! base_Addr = 0xe88c8400
[ 2.065612] twi2, apb clock = 24000000
[ 2.069647] I2C: i2c-2: AW16XX I2C adapter
[ 2.073764] **********start************
[ 2.077596] 0x40
[ 2.079518] 0xf8
[ 2.081490] 0x58
[ 2.083413] 0x0
[ 2.085249] 0x0
[ 2.087084] **********end************
[ 2.090901] lirc_dev: IR Remote Control driver registered, major 250
[ 2.097340] IR NEC protocol handler initialized
[ 2.101888] IR RC5(x) protocol handler initialized
[ 2.106675] IR RC6 protocol handler initialized
[ 2.111216] IR JVC protocol handler initialized
[ 2.115741] IR Sony protocol handler initialized
[ 2.120370] IR RC5 (streamzap) protocol handler initialized
[ 2.125935] IR LIRC bridge handler initialized
[ 2.130388] Linux video capture interface: v2.00
[ 2.135024] [ace_drv] start!!!
[ 2.138386] [ace_drv] init end!!!
[ 2.141779] [pa_drv] start!!!
[ 2.145074] [pa_drv] init end!!!
[ 2.148414] print_constraints: axp20_ldo1: 1300 mV
[ 2.154309] print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[ 2.161921] print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[ 2.169426] print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[ 2.177095] print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV
[ 2.184832] print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV
[ 2.191993] print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[ 2.199156] input: axp20-supplyer as /devices/platform/sun4i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
[ 2.215220] pmu_pekoff_time = 6000
[ 2.218917] pmu_pekoff_en = 1
[ 2.221924] pmu_peklong_time = 1500
[ 2.225913] ehci_irq: port change detect
[ 2.229885] pmu_pekon_time = 1000
[ 2.233225] pmu_pwrok_time = 64
[ 2.236364] pmu_pwrnoe_time = 2000
[ 2.239760] pmu_intotp_en = 1
[ 2.243225] [AXP]POWER20_OFF_CTL:1908-->0x42
[ 2.247950] POWER20_PEK_SET:1925-->0x9d
[ 2.252270] POWER20_PEK_SET:1936-->0x9d
[ 2.256568] POWER20_PEK_SET:1945-->0x9d
[ 2.260885] POWER20_PEK_SET:1956-->0x9d
[ 2.265183] POWER20_PEK_SET:1968-->0x9d
[ 2.269482] POWER20_HOTOVER_CTL:1977-->0xad
[ 2.277155] [AXP]last_rest_vol = 0, now_rest_vol = 100
[ 2.282347] The port change to OHCI now!
[ 2.287777] [AXP]Cur_CoulombCounter = 0
[ 2.291636] [AXP]charger->rest_vol = 100
[ 2.298525] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 2.307397] device-mapper: multipath: version 1.3.0 loaded
[ 2.312935] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.319458] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 2.326115] device-mapper: multipath service-time: version 0.2.0 loaded
[ 2.333020] Bluetooth: HCI UART driver ver 2.2
[ 2.337464] Bluetooth: HCI H4 protocol initialized
[ 2.342278] Bluetooth: HCI BCSP protocol initialized
[ 2.347239] Bluetooth: HCILL protocol initialized
[ 2.352013] [wifi]: Select sdio wifi: swl-n20 !!
[ 2.356839] [mmc_pm]: SDIO card gpio init is OK !!
[ 2.361722] [mmc]: sunximmc_init
[ 2.365202] [mmc]: sunxi mmc controller using config : 0xb
[ 2.370757] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[ 2.377207] [mmc]: mmc 0 power off !!
[ 2.381053] [mmc]: mmc0 Probe: base:0xe88cc000 irq:32 dma:0 pdes:0xe700c000, ret 0.
[ 2.388722] [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
[ 2.395204] [mmc]: mmc 1 power off !!
[ 2.398936] [mmc]: mmc1 Probe: base:0xe88ce000 irq:33 dma:0 pdes:0xe7014000, ret 0.
[ 2.406666] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[ 2.413066] [mmc]: mmc 3 power off !!
[ 2.416792] [mmc]: mmc3 Probe: base:0xe88d0000 irq:35 dma:0 pdes:0xe7018000, ret 0.
[ 2.424544] sb-pwm: pwm_request 303, id=0, label=pwm1
[ 2.429667] Registered led device: pwm1
[ 2.433525] sb-pwm: pwm_request 303, id=1, label=pwm2
[ 2.438634] Registered led device: pwm2
[ 2.442552] sb-pwm: pwm_request 303, id=2, label=pwm0
[ 2.447665] Registered led device: pwm0
[ 2.451523] sb-pwm: pwm_request 303, id=3, label=pwm3
[ 2.456650] Registered led device: pwm3
[ 2.460521] sb-pwm: pwm_request 303, id=4, label=pwm4
[ 2.465636] Registered led device: pwm4
[ 2.469470] sb-pwm: pwm_request 303, id=5, label=pwm5
[ 2.474599] Registered led device: pwm5
[ 2.486154] input: Topre Corporation HHKB Professional as /devices/platform/sw-ohci.1/usb3/3-1/3-1:1.0/input/input1
[ 2.496861] generic-usb 0003:0853:0100.0001: input: USB HID v1.11 Keyboard [Topre Corporation HHKB Professional] on usb-sw-ohci-1/input0
[ 2.509249] usbcore: registered new interface driver usbhid
[ 2.514839] usbhid: USB HID core driver
[ 2.519047] logger: created 256K log 'log_main'
[ 2.523751] logger: created 256K log 'log_events'
[ 2.528535] logger: created 256K log 'log_radio'
[ 2.533255] logger: created 256K log 'log_system'
[ 2.538614] enter sun4i Audio codec!!!
[ 2.542798] sun4i-codec: probe of sun4i-codec failed with error -1
[ 2.549753] soc_new_pcm,line:2112
[ 2.553328] asoc: sndhdmi <-> sun4i-hdmiaudio.0 mapping ok
[ 2.559148] ALSA device list:
[ 2.562146] #0: sndhdmi
[ 2.565058] IPv4 over IPv4 tunneling driver
[ 2.569538] GRE over IPv4 demultiplexor driver
[ 2.573842] GRE over IPv4 tunneling driver
[ 2.578490] TCP cubic registered
[ 2.581793] usb 5-1: new low speed USB device number 2 using sw-ohci
[ 2.588200] Initializing XFRM netlink socket
[ 2.592541] NET: Registered protocol family 17
[ 2.597024] NET: Registered protocol family 15
[ 2.601625] Bluetooth: RFCOMM TTY layer initialized
[ 2.606508] Bluetooth: RFCOMM socket layer initialized
[ 2.611727] Bluetooth: RFCOMM ver 1.11
[ 2.615475] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.620822] Bluetooth: BNEP filters: protocol multicast
[ 2.626046] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.632072] L2TP core driver, V2.0
[ 2.635471] L2TP IP encapsulation support (L2TPv3)
[ 2.640366] L2TP netlink interface
[ 2.643789] L2TP ethernet pseudowire support (L2TPv3)
[ 2.649232] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 2.657292] dram_sysdev_init finished!
[ 2.661470] [LCD] lcd_module_init
[ 2.721974] out_csc=0
[ 2.730571] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on
[ 2.738563] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on
[ 2.746642] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on
[ 2.754663] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on
[ 2.762630] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on
[ 2.770611] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 2.775408] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:8:34
[ 2.780960] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:08:34 UTC (1262304514)
[ 2.790738] Freeing init memory: 5108K
[ 2.808523] mount used greatest stack depth: 6248 bytes left
[ 2.815700] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/sw-ohci.2/usb5/5-1/5-1:1.0/input/input2
[ 2.837233] generic-usb 0003:045E:0040.0002: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-sw-ohci-1/i
nput0
/dev/nandd
e2fsck 1.42.7 (21-Jan-2013)
/dev/nandd: recovering journal
[ 3.197714] set to HDMI mode
[ 3.200676] get_hdmi_mode == HDMI
/dev/nandd: clean, 54178/96000 f[ 3.705699] e2fsck used greatest stack depth: 6080 bytes left
iles, 208009/384000 blocks
[ 3.719022] EXT3-fs (nandd): using internal journal
[ 3.724008] kjournald starting. Commit interval 5 seconds
[ 3.729514] EXT3-fs (nandd): mounted filesystem with ordered data mode
[ 4.087201] hostname used greatest stack depth: 5648 bytes left
[ 4.191421] plymouthd used greatest stack depth: 5208 bytes left
[ 4.306631] init: ureadahead main process (67) terminated with status 5
[ 4.721986] grep used greatest stack depth: 5056 bytes left
[ 4.976680] list-records used greatest stack depth: 5016 bytes left
mountall: Disconnected from Plymouth
fsck from util-linux 2.20.1
/dev/nande: recovering journal
/dev/nande: clean, 146/20496 files, 6228/81920 blocks
Welcome to Linaro 12.07 (GNU/Linux 3.0.8+ armv7l)
* Documentation: https://wiki.linaro.org/
[ 9.014521] android_usb: already disabled
root@ubuntu:~#
|
●データシート・ファイル (うまく表示されない場合は、右クリックしてファイルに保存してから開いてください)
|
|
pcDuino_V01_Schem.pdf
(366kバイト) 2013年 02月 28日
pcDuino_UserGuide_Rev02.pdf
(1,728kバイト) 2013年 02月 28日
pcduino-boot.txt
(28kバイト) 2013年 04月 23日
| ●その他の質問一覧（この商品について）
|
 起動ログ 2013-04-23更新 |
|
