HELLO! BOOT0 is starting! boot0 version : 1.5.0 dram size =1024 Succeed in opening nand flash. Succeed in reading Boot1 file head. The size of Boot1 is 0x00056000. The file stored in 0X00000000 of block 2 is perfect. Check is correct. Ready to disable icache. Succeed in loading Boot1. Jump to Boot1. [ 0.179] boot1 version : 1.5.0 [ 0.179] pmu type = 3 [ 0.180] bat vol = 0 [ 0.212] axi:ahb:apb=3:2:2 [ 0.212] set dcdc2=1400, clock=1008 successed [ 0.214] key [ 0.227] no key found [ 0.227] flash init start [ 0.596] flash init finish [ 0.598] fs init ok [ 0.599] fattype FAT16 [ 0.599] fs mount ok [ 0.605] script finish [ 0.606] power finish [ 0.614] BootMain start [ 0.614] 0 [ 0.629] usbdc_vol = 4000, usbdc_cur = 0 [ 0.629] usbpc_vol = 4000, usbpc_cur = 0 [ 0.632] init to usb pc [ 0.635] set pc [ 0.725] power_start=0x00000002 [ 0.725] pre sys mode [ 0.725] startup status = -1 [ 0.728] key value = 0 [ 0.731] recovery key high 6, low 4 [ 0.735] unable to find fastboot_key key_max value [ 0.743] test for multi os boot with display [ 1.367] show pic finish [ 1.367] load kernel start [ 1.385] load kernel successed [ 1.385] start address = 0x4a000000 [ 1.387] power exit detect [ U-Boot 2011.09-rc1-svn98 (Mar 07 2013 - 15:03:53) Allwinner Technology CPU: SUNXI Family Board: A10-EVB DRAM: 512 MiB NAND: 1900 MiB In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:5- -name- -start- -size- bootloader : 1000000 2000000 env : 3000000 1000000 boot : 4000000 1000000 rootfs : 5000000 5dc00000 UDISK : 62c00000 14000000 ----------------------------------- no misc partition is found Hit any key to stop autoboot: 3  2  1  0 reading evb.bin 44792 bytes read reading uImage 6225524 bytes read ## Booting kernel from Legacy Image at 48000000 ... Image Name: Linux-3.0.8+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6225460 Bytes = 5.9 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... DRAM: 1024 MB[ 0.000000] Linux version 3.0.8+ (ubuntu@linux-server) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 PREEMPT Thu Mar 7 15:02: 13 CST 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: sun4i [ 0.000000] Total Detected Memory: 1024MB with 2 banks [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Memory Reserved(in bytes): [ 0.000000] LCD: 0x5a000000, 0x02000000 [ 0.000000] SYS: 0x43000000, 0x00010000 [ 0.000000] G2D: 0x58000000, 0x01000000 [ 0.000000] VE : 0x44000000, 0x05000000 [ 0.000000] VE : 0x49000000, 0x01000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 245760 [ 0.000000] free_area_init_node: node 0, pgdat c0c0a110, node_mem_map c0dc9000 [ 0.000000] Normal zone: 1280 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 146176 pages, LIFO batch:31 [ 0.000000] HighMem zone: 768 pages used for memmap [ 0.000000] HighMem zone: 97536 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243712 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/nandd init=/init loglevel=8 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 448MB 512MB = 960MB total [ 0.000000] Memory: 829264k/829264k available, 153776k reserved, 393216K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xe8800000 - 0xf0000000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe8000000 ( 640 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0008000 - 0xc0505000 (5108 kB) [ 0.000000] .text : 0xc0505000 - 0xc0bc6b10 (6919 kB) [ 0.000000] .data : 0xc0bc8000 - 0xc0c133a0 ( 301 kB) [ 0.000000] .bss : 0xc0c133c4 - 0xc0dc8110 (1748 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:96 nr_irqs:96 96 [ 0.000000] timer0: Periodic Mode [ 0.000000] sw_timer_init,line:424 [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] aw_clksrc_init, line:338 [ 0.000000] Console: colour dummy device 80x30 [ 0.000093] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408) [ 0.040022] pid_max: default: 32768 minimum: 301 [ 0.040146] Mount-cache hash table entries: 512 [ 0.040427] CPU: Testing write buffer coherency: ok [ 0.040601] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.041033] devtmpfs: initialized [ 0.042263] print_constraints: dummy: [ 0.042361] NET: Registered protocol family 16 [ 0.042947] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.043393] try to parse pll6 frequency from script faild! [ 0.043433] try to parse apb frequency from script faild! [ 0.043502] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics [ 0.043559] Initialize DMAC OK [ 0.043596] sb-pwm: sb_pwm_init 513 [ 0.043896] sb-pwm: sb_pwm_probe 345 [ 0.043917] sb-pwm: sb_pwm_probe 345 [ 0.043933] sb-pwm: sb_pwm_probe 345 [ 0.043947] sb-pwm: sb_pwm_probe 345 [ 0.043963] sb-pwm: sb_pwm_probe 345 [ 0.043977] sb-pwm: sb_pwm_probe 345 [ 0.048138] bio: create slab at 0 [ 0.048679] SCSI subsystem initialized [ 0.048876] usbcore: registered new interface driver usbfs [ 0.048946] usbcore: registered new interface driver hub [ 0.049074] usbcore: registered new device driver usb [ 0.049414] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.049716] Bluetooth: Core ver 2.16 [ 0.049761] NET: Registered protocol family 31 [ 0.049770] Bluetooth: HCI device and connection manager initialized [ 0.049785] Bluetooth: HCI socket layer initialized [ 0.049794] Bluetooth: L2CAP socket layer initialized [ 0.049816] Bluetooth: SCO socket layer initialized [ 0.050000] cfg80211: Calling CRDA to update world regulatory domain [ 0.050000] Init eGon pin module V2.0 [ 0.050000] Switching to clocksource aw 64bits couter [ 0.050000] FS-Cache: Loaded [ 0.050000] CacheFiles: Loaded [ 0.050000] Switched to NOHz mode on CPU #0 [ 0.050000] [usb_manager]: CONFIG_USB_SW_SUN4I_USB0_OTG [ 0.050000] [sw_hcd0]: usb host driver initialize........ [ 0.050000] [sw_hcd0]: open_usb_clock [ 0.066422] [sw_hcd0]: host_init_state = 0 [ 0.066431] [sw_hcd0]: platform is usb host [ 0.066495] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38 [ 0.066520] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver [ 0.066535] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1 [ 0.067049] hub 1-0:1.0: USB hub found [ 0.067075] hub 1-0:1.0: 1 port detected [ 0.067098] wrn: hcd is not enable, need not start hcd [ 0.067342] [sw_hcd0]: sw_usb_host0_disable start [ 0.067356] -------sw_hcd0_soft_disconnect--------- [ 0.067367] [sw_hcd_host0]: Set USB Power OFF [ 0.067376] wrn: hcd is not enable, need not stop hcd [ 0.067403] [sw_hcd0]: close_usb_clock [ 0.067445] [sw_hcd0]: sw_usb_host0_disable end [ 0.067480] [sw_udc]: udc_init: version 20080411 [ 0.067709] axp driver uning configuration failed(539) [ 0.067729] axp driver uning configuration failed(551) [ 0.067881] NET: Registered protocol family 2 [ 0.067985] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.068320] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.070427] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 0.071117] TCP: Hash tables configured (established 131072 bind 65536) [ 0.071127] TCP reno registered [ 0.071139] UDP hash table entries: 512 (order: 1, 8192 bytes) [ 0.071162] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes) [ 0.071342] NET: Registered protocol family 1 [ 0.071635] RPC: Registered named UNIX socket transport module. [ 0.071647] RPC: Registered udp transport module. [ 0.071654] RPC: Registered tcp transport module. [ 0.071662] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.091616] PMU: registered new PMU device of type 0 [ 0.091683] [pm]aw_pm_init! [ 0.108342] highmem bounce pool size: 64 pages [ 0.108578] ashmem: initialized [ 0.114138] VFS: Disk quotas dquot_6.5.2 [ 0.114308] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.117382] NTFS driver 2.1.30 [Flags: R/W]. [ 0.117822] fuse init (API version 7.16) [ 0.118429] msgmni has been set to 851 [ 0.118850] cryptomgr_test used greatest stack depth: 6672 bytes left [ 0.119250] cryptomgr_test used greatest stack depth: 6480 bytes left [ 0.121374] cryptomgr_test used greatest stack depth: 6388 bytes left [ 0.122399] cryptomgr_test used greatest stack depth: 6280 bytes left [ 0.122849] alg: No test for stdrng (krng) [ 0.123048] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.123063] io scheduler noop registered [ 0.123071] io scheduler deadline registered [ 0.123143] io scheduler cfq registered (default) [ 0.123752] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.124962] serial8250.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A [ 0.836277] console [ttyS0] enabled [ 0.840496] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A [ 0.847693] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A [ 0.855400] brd: module loaded [ 0.860524] loop: module loaded [ 0.863675] [NAND]nand driver, init. [ 0.867247] cmu_clk is 408 [ 0.870068] nand clk init end [ 0.873120] offset 0xc: 0x6040 [ 0.876343] offset 0x14: 0x8200000a [ 0.880000] [NAND] nand gpio_request [ 0.883615] [NAND] nand driver version: 0x2 0x9 [ 0.888244] nand interrupte register ok [ 0.892098] ret of NFC_ChangMode is 0 [ 0.895842] dma_hdle is 0 [ 0.898635] dma_hdle is 10000008 [ 0.902129] cmu_clk is 408 [ 0.904920] nand clk init end [ 0.907962] offset 0xc: 0x6040 [ 0.911205] offset 0x14: 0x82000006 [ 0.928140] The 0 disk name = DEVICE, class name = NAND, disk start = 0, disk size = 3891200 [ 0.938464] The 1 disk name = bootloader, type = 0, class name = DISK, disk size = 65536 [ 0.946589] The 2 disk name = env, type = 0, class name = DISK, disk size = 32768 [ 0.954092] The 3 disk name = boot, type = 0, class name = DISK, disk size = 32768 [ 0.961673] The 4 disk name = rootfs, type = 0, class name = DISK, disk size = 3072000 [ 0.969582] The 5 disk name = UDISK, type = 0, class name = DISK, disk size = 655360 [ 0.977337] The 5 disk size = 655360 [ 0.980924] part total count = 6 [ 0.985273] nand: unknown partition table [ 0.990327] nanda: [ 0.993483] nandb: unknown partition table [ 0.998691] nandc: unknown partition table [ 1.108980] nandd: unknown partition table [ 1.114255] nande: unknown partition table [ 1.118597] benn: nand probe enter [ 1.122083] [NAND]nand driver, ok. [ 1.125548] sun4i gpio driver init [ 1.129441] test_adc_init [ 1.132374] [spi]: Found 2 spi devices in config files [ 1.137514] boards_num modalias max_spd_hz bus_num cs mode [ 1.145028] 0 spidev 12000000 0 0 3 [ 1.152532] 1 spidev 12000000 2 0 3 [ 1.160241] [spi-0]: cs bitmap from cfg = 0x1 [ 1.164892] [spi-0]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000 [ 1.172334] reuuimllas SoC SPI Driver loaded for Bus SPI-0 with 2 Slaves at most [ 1.179726] [spi-0]: driver probe succeed, base e88b8000, irq 10, dma_id_rx 43, dma_id_tx 44! [ 1.188289] [spi-2]: cs bitmap from cfg = 0x1 [ 1.192887] [spi-2]: source = sdram_pll_p, src_clk = 408000000, mclk 102000000 [ 1.200293] reuuimllas SoC SPI Driver loaded for Bus SPI-2 with 2 Slaves at most [ 1.207683] [spi-2]: driver probe succeed, base e88ba000, irq 12, dma_id_rx 45, dma_id_tx 46! [ 1.216584] tun: Universal TUN/TAP device driver, 1.6 [ 1.221663] tun: (C) 1999-2004 Max Krasnyansky [ 1.227964] wemac Ethernet Driver, V1.00 in file:drivers/net/sun4i/sun4i_wemac.c [ 1.235557] can't get information emac_power gpio [ 1.240307] [EMAC] ahb clk enable [ 1.243706] [EMAC] ahb gate clk: 0x526040 [ 1.257873] wemac wemac.0: PHY SETUP, reg 0 value: 3100 [ 1.263115] emac MAC isn't valid! [ 1.267423] wemac wemac.0: resetting device [ 1.272338] release temp resource [ 1.275701] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.282298] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.288705] [sw-ehci1]: probe, pdev->name: sw-ehci, pdev->id: 1, sw_ehci: 0xc0cbeef4 [ 1.296472] [sw-ehci1]: open clock [ 1.319825] [sw-ehci1]: Set USB Power ON [ 1.323769] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.331281] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2 [ 1.338410] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000 [ 1.360041] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00 [ 1.365439] ehci_irq: port change detect [ 1.369853] hub 2-0:1.0: USB hub found [ 1.373651] hub 2-0:1.0: 1 port detected [ 1.377929] [sw-ohci1]: probe, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc0cbf00c [ 1.385698] [sw-ohci1]: open clock [ 1.409044] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.416210] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3 [ 1.423302] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400 [ 1.484460] hub 3-0:1.0: USB hub found [ 1.488221] hub 3-0:1.0: 1 port detected [ 1.492470] [sw-ehci2]: probe, pdev->name: sw-ehci, pdev->id: 2, sw_ehci: 0xc0cbf128 [ 1.500232] [sw-ehci2]: open clock [ 1.523576] [sw-ehci2]: Set USB Power ON [ 1.527498] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.535014] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4 [ 1.542155] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000 [ 1.560039] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00 [ 1.565436] ehci_irq: port change detect [ 1.569752] hub 4-0:1.0: USB hub found [ 1.573627] hub 4-0:1.0: 1 port detected [ 1.577856] [sw-ohci2]: probe, pdev->name: sw-ohci, pdev->id: 2, sw_ohci: 0xc0cbf240 [ 1.585641] [sw-ohci2]: open clock [ 1.609022] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.616188] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5 [ 1.623275] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400 [ 1.630048] ehci_irq: port change detect [ 1.684443] hub 5-0:1.0: USB hub found [ 1.688203] hub 5-0:1.0: 1 port detected [ 1.692202] The port change to OHCI now! [ 1.696371] Initializing USB Mass Storage driver... [ 1.701438] usbcore: registered new interface driver usb-storage [ 1.707439] USB Mass Storage support registered. [ 1.712126] usbcore: registered new interface driver ums-alauda [ 1.718085] usbcore: registered new interface driver ums-cypress [ 1.724149] usbcore: registered new interface driver ums-datafab [ 1.730233] usbcore: registered new interface driver ums_eneub6250 [ 1.736445] usbcore: registered new interface driver ums-freecom [ 1.742508] usbcore: registered new interface driver ums-isd200 [ 1.748460] usbcore: registered new interface driver ums-jumpshot [ 1.754609] usbcore: registered new interface driver ums-karma [ 1.760495] usbcore: registered new interface driver ums-onetouch [ 1.766636] usbcore: registered new interface driver ums-realtek [ 1.772744] usbcore: registered new interface driver ums-sddr09 [ 1.778699] usbcore: registered new interface driver ums-sddr55 [ 1.784678] usbcore: registered new interface driver ums-usbat [ 1.790678] usbcore: registered new interface driver usbserial [ 1.796506] usbserial: USB Serial Driver core [ 1.800918] USB Serial support registered for GSM modem (1-port) [ 1.807105] usbcore: registered new interface driver option [ 1.812719] option: v0.7.2:USB Driver for GSM modems [ 1.817715] ------print_msc_config----- [ 1.821567] vendor_id = 0x18d1 [ 1.825659] mass_storage_id = 0x1 [ 1.829489] adb_id = 0x2 [ 1.833337] usb_manufacturer_name = USB Developer [ 1.838035] usb_product_name = Android [ 1.842230] usb_serial_number = 20080411 [ 1.846495] msc_vendor_name = USB 2.0 [ 1.850736] msc_product_name = USB Flash Driver [ 1.855696] msc_release = 100 [ 1.859527] luns = 1 [ 1.863218] --------------------------- [ 1.867204] [sw_udc]: [sw_usb_udc]: binding gadget driver 'android_usb' [ 1.873871] [sw_udc]: alloc request: ep(0xc0bf4138, ep0, 64), req(0xe7bb29c0) [ 1.881036] WRN:L2703(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active [ 1.889044] [sw_udc]: sw_udc_pullup, is_on = 0 [ 1.893514] WRN:L2738(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active [ 1.902770] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 1.909643] android_usb gadget: Number of LUNs=1 [ 1.914300] lun0: LUN: removable file: (no medium) [ 1.919188] lun name: lun [ 1.922004] WRN:L2703(drivers/usb/sun4i_usb/udc/sw_udc.c):ERR: usb device is not active [ 1.930078] android_usb gadget: android_usb ready [ 1.934918] mousedev: PS/2 mouse device common for all mice [ 1.941155] sunxi RTC version 0.1 [ 1.944703] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380239881 [ 1.951248] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime [ 1.956040] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:8:33 [ 1.961768] using rtc device, rtc, for alarms [ 1.965978] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 [ 1.972327] i2c /dev entries driver [ 1.975922] !!! base_Addr = 0xe88c4c00 [ 1.979764] config i2c gpio with gpio_config api [ 1.984527] twi0, apb clock = 24000000 [ 1.989660] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected [ 1.995028] usb 3-1: new full speed USB device number 2 using sw-ohci [ 2.002656] [AXP]axp driver uning configuration failed(324) [ 2.008287] [AXP]power_start = 0 [ 2.011562] I2C: i2c-0: AW16XX I2C adapter [ 2.015654] **********start************ [ 2.019486] 0x40 [ 2.021443] 0xf8 [ 2.023366] 0x28 [ 2.025288] 0x0 [ 2.027124] 0x0 [ 2.028960] **********end************ [ 2.032680] !!! base_Addr = 0xe88c6000 [ 2.036551] twi1, apb clock = 24000000 [ 2.040650] I2C: i2c-1: AW16XX I2C adapter [ 2.044743] **********start************ [ 2.048574] 0x40 [ 2.050524] 0xf8 [ 2.052447] 0x58 [ 2.054369] 0x0 [ 2.056204] 0x0 [ 2.058039] **********end************ [ 2.061756] !!! base_Addr = 0xe88c8400 [ 2.065612] twi2, apb clock = 24000000 [ 2.069647] I2C: i2c-2: AW16XX I2C adapter [ 2.073764] **********start************ [ 2.077596] 0x40 [ 2.079518] 0xf8 [ 2.081490] 0x58 [ 2.083413] 0x0 [ 2.085249] 0x0 [ 2.087084] **********end************ [ 2.090901] lirc_dev: IR Remote Control driver registered, major 250 [ 2.097340] IR NEC protocol handler initialized [ 2.101888] IR RC5(x) protocol handler initialized [ 2.106675] IR RC6 protocol handler initialized [ 2.111216] IR JVC protocol handler initialized [ 2.115741] IR Sony protocol handler initialized [ 2.120370] IR RC5 (streamzap) protocol handler initialized [ 2.125935] IR LIRC bridge handler initialized [ 2.130388] Linux video capture interface: v2.00 [ 2.135024] [ace_drv] start!!! [ 2.138386] [ace_drv] init end!!! [ 2.141779] [pa_drv] start!!! [ 2.145074] [pa_drv] init end!!! [ 2.148414] print_constraints: axp20_ldo1: 1300 mV [ 2.154309] print_constraints: axp20_ldo2: 1800 <--> 3300 mV at 3000 mV [ 2.161921] print_constraints: axp20_ldo3: 700 <--> 3500 mV at 2800 mV [ 2.169426] print_constraints: axp20_ldo4: 1250 <--> 3300 mV at 2800 mV [ 2.177095] print_constraints: axp20_buck2: 700 <--> 2275 mV at 1400 mV [ 2.184832] print_constraints: axp20_buck3: 700 <--> 3500 mV at 1250 mV [ 2.191993] print_constraints: axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV [ 2.199156] input: axp20-supplyer as /devices/platform/sun4i-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0 [ 2.215220] pmu_pekoff_time = 6000 [ 2.218917] pmu_pekoff_en = 1 [ 2.221924] pmu_peklong_time = 1500 [ 2.225913] ehci_irq: port change detect [ 2.229885] pmu_pekon_time = 1000 [ 2.233225] pmu_pwrok_time = 64 [ 2.236364] pmu_pwrnoe_time = 2000 [ 2.239760] pmu_intotp_en = 1 [ 2.243225] [AXP]POWER20_OFF_CTL:1908-->0x42 [ 2.247950] POWER20_PEK_SET:1925-->0x9d [ 2.252270] POWER20_PEK_SET:1936-->0x9d [ 2.256568] POWER20_PEK_SET:1945-->0x9d [ 2.260885] POWER20_PEK_SET:1956-->0x9d [ 2.265183] POWER20_PEK_SET:1968-->0x9d [ 2.269482] POWER20_HOTOVER_CTL:1977-->0xad [ 2.277155] [AXP]last_rest_vol = 0, now_rest_vol = 100 [ 2.282347] The port change to OHCI now! [ 2.287777] [AXP]Cur_CoulombCounter = 0 [ 2.291636] [AXP]charger->rest_vol = 100 [ 2.298525] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 2.307397] device-mapper: multipath: version 1.3.0 loaded [ 2.312935] device-mapper: multipath round-robin: version 1.0.0 loaded [ 2.319458] device-mapper: multipath queue-length: version 0.1.0 loaded [ 2.326115] device-mapper: multipath service-time: version 0.2.0 loaded [ 2.333020] Bluetooth: HCI UART driver ver 2.2 [ 2.337464] Bluetooth: HCI H4 protocol initialized [ 2.342278] Bluetooth: HCI BCSP protocol initialized [ 2.347239] Bluetooth: HCILL protocol initialized [ 2.352013] [wifi]: Select sdio wifi: swl-n20 !! [ 2.356839] [mmc_pm]: SDIO card gpio init is OK !! [ 2.361722] [mmc]: sunximmc_init [ 2.365202] [mmc]: sunxi mmc controller using config : 0xb [ 2.370757] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0 [ 2.377207] [mmc]: mmc 0 power off !! [ 2.381053] [mmc]: mmc0 Probe: base:0xe88cc000 irq:32 dma:0 pdes:0xe700c000, ret 0. [ 2.388722] [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1 [ 2.395204] [mmc]: mmc 1 power off !! [ 2.398936] [mmc]: mmc1 Probe: base:0xe88ce000 irq:33 dma:0 pdes:0xe7014000, ret 0. [ 2.406666] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3 [ 2.413066] [mmc]: mmc 3 power off !! [ 2.416792] [mmc]: mmc3 Probe: base:0xe88d0000 irq:35 dma:0 pdes:0xe7018000, ret 0. [ 2.424544] sb-pwm: pwm_request 303, id=0, label=pwm1 [ 2.429667] Registered led device: pwm1 [ 2.433525] sb-pwm: pwm_request 303, id=1, label=pwm2 [ 2.438634] Registered led device: pwm2 [ 2.442552] sb-pwm: pwm_request 303, id=2, label=pwm0 [ 2.447665] Registered led device: pwm0 [ 2.451523] sb-pwm: pwm_request 303, id=3, label=pwm3 [ 2.456650] Registered led device: pwm3 [ 2.460521] sb-pwm: pwm_request 303, id=4, label=pwm4 [ 2.465636] Registered led device: pwm4 [ 2.469470] sb-pwm: pwm_request 303, id=5, label=pwm5 [ 2.474599] Registered led device: pwm5 [ 2.486154] input: Topre Corporation HHKB Professional as /devices/platform/sw-ohci.1/usb3/3-1/3-1:1.0/input/input1 [ 2.496861] generic-usb 0003:0853:0100.0001: input: USB HID v1.11 Keyboard [Topre Corporation HHKB Professional] on usb-sw-ohci-1/input0 [ 2.509249] usbcore: registered new interface driver usbhid [ 2.514839] usbhid: USB HID core driver [ 2.519047] logger: created 256K log 'log_main' [ 2.523751] logger: created 256K log 'log_events' [ 2.528535] logger: created 256K log 'log_radio' [ 2.533255] logger: created 256K log 'log_system' [ 2.538614] enter sun4i Audio codec!!! [ 2.542798] sun4i-codec: probe of sun4i-codec failed with error -1 [ 2.549753] soc_new_pcm,line:2112 [ 2.553328] asoc: sndhdmi <-> sun4i-hdmiaudio.0 mapping ok [ 2.559148] ALSA device list: [ 2.562146] #0: sndhdmi [ 2.565058] IPv4 over IPv4 tunneling driver [ 2.569538] GRE over IPv4 demultiplexor driver [ 2.573842] GRE over IPv4 tunneling driver [ 2.578490] TCP cubic registered [ 2.581793] usb 5-1: new low speed USB device number 2 using sw-ohci [ 2.588200] Initializing XFRM netlink socket [ 2.592541] NET: Registered protocol family 17 [ 2.597024] NET: Registered protocol family 15 [ 2.601625] Bluetooth: RFCOMM TTY layer initialized [ 2.606508] Bluetooth: RFCOMM socket layer initialized [ 2.611727] Bluetooth: RFCOMM ver 1.11 [ 2.615475] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.620822] Bluetooth: BNEP filters: protocol multicast [ 2.626046] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.632072] L2TP core driver, V2.0 [ 2.635471] L2TP IP encapsulation support (L2TPv3) [ 2.640366] L2TP netlink interface [ 2.643789] L2TP ethernet pseudowire support (L2TPv3) [ 2.649232] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.657292] dram_sysdev_init finished! [ 2.661470] [LCD] lcd_module_init [ 2.721974] out_csc=0 [ 2.730571] regulator_init_complete: axp20_buck3: incomplete constraints, leaving on [ 2.738563] regulator_init_complete: axp20_buck2: incomplete constraints, leaving on [ 2.746642] regulator_init_complete: axp20_ldo4: incomplete constraints, leaving on [ 2.754663] regulator_init_complete: axp20_ldo3: incomplete constraints, leaving on [ 2.762630] regulator_init_complete: axp20_ldo2: incomplete constraints, leaving on [ 2.770611] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime [ 2.775408] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:8:34 [ 2.780960] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:08:34 UTC (1262304514) [ 2.790738] Freeing init memory: 5108K [ 2.808523] mount used greatest stack depth: 6248 bytes left [ 2.815700] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/sw-ohci.2/usb5/5-1/5-1:1.0/input/input2 [ 2.837233] generic-usb 0003:045E:0040.0002: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-sw-ohci-1/i nput0 /dev/nandd e2fsck 1.42.7 (21-Jan-2013) /dev/nandd: recovering journal [ 3.197714] set to HDMI mode [ 3.200676] get_hdmi_mode == HDMI /dev/nandd: clean, 54178/96000 f[ 3.705699] e2fsck used greatest stack depth: 6080 bytes left iles, 208009/384000 blocks [ 3.719022] EXT3-fs (nandd): using internal journal [ 3.724008] kjournald starting. Commit interval 5 seconds [ 3.729514] EXT3-fs (nandd): mounted filesystem with ordered data mode [ 4.087201] hostname used greatest stack depth: 5648 bytes left [ 4.191421] plymouthd used greatest stack depth: 5208 bytes left [ 4.306631] init: ureadahead main process (67) terminated with status 5 [ 4.721986] grep used greatest stack depth: 5056 bytes left [ 4.976680] list-records used greatest stack depth: 5016 bytes left mountall: Disconnected from Plymouth fsck from util-linux 2.20.1 /dev/nande: recovering journal /dev/nande: clean, 146/20496 files, 6228/81920 blocks Welcome to Linaro 12.07 (GNU/Linux 3.0.8+ armv7l) * Documentation: https://wiki.linaro.org/ [ 9.014521] android_usb: already disabled root@ubuntu:~#