シリアルから出力される起動メッセージです。参考にしてください。
U-Boot SPL 2014.01-rc1-09130-g4e491b0 (Dec 12 2013 - 15:15:19)
Board: A10-OLinuXino-Lime
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600
U-Boot 2014.01-rc1-09130-g4e491b0 (Dec 12 2013 - 15:15:19) Allwinner Technology
CPU: Allwinner A10 (SUN4I)
Board: A10-OLinuXino-Lime
I2C: ready
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: emac
Hit any key to stop autoboot: 0
reading uEnv.txt
104 bytes read in 10 ms (9.8 KiB/s)
Loaded environment from uEnv.txt
reading boot.scr
337 bytes read in 2 ms (164.1 KiB/s)
Jumping to boot.scr
## Executing script at 44000000
reading script.bin
49804 bytes read in 6 ms (7.9 MiB/s)
reading uImage
4408744 bytes read in 195 ms (21.6 MiB/s)
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.4.67+
Created: 2013-12-14 13:12:26 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4408680 Bytes = 4.2 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<5>Linux version 3.4.67+ (root@debian) (gcc version 4.7.1 (Debian 4.7.1-7) ) #4 PREEMPT Sat Dec 14 15:12:10 EET 2013
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun4i
<6>Memory cut off:
<6> MALI : 0x5c000000 - 0x5fffffff ( 64 MB)
<4>Ignoring unrecognised tag 0x00000000
<6>Memory Reserved:
<6> SYS : 0x43000000 - 0x4300ffff ( 64 kB)
<6> VE : 0x44000000 - 0x48ffffff ( 80 MB)
<6> LCD : 0x5a000000 - 0x5affffff ( 16 MB)
Memory policy: ECC disabled, Data cache writeback
<6>sunxi: Allwinner A10 revision C (AW1623/sun4i) detected.
<7>On node 0 totalpages: 114688
<7>free_area_init_node: node 0, pgdat c0844e88, node_mem_map c0a0d000
<7> Normal zone: 896 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 113792 pages, LIFO batch:31
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
<5>Kernel command line: console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1280x720p50 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 root
=/dev/mmcblk0p2 rootwait panic=10
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 448MB = 448MB total
<5>Memory: 346060k/346060k available, 112692k reserved, 0K highmem
<5>Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xdc800000 - 0xff000000 ( 552 MB)
lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc07b67b8 (7866 kB)
.init : 0xc07b7000 - 0xc07e2000 ( 172 kB)
.data : 0xc07e2000 - 0xc084fd28 ( 440 kB)
.bss : 0xc084fd4c - 0xc0a0c0a8 (1777 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>NR_IRQS:128
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>CPU: Testing write buffer coherency: ok
<6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
<6>Setting up static identity map for 0x40555480 - 0x405554d8
<6>devtmpfs: initialized
<6>dummy:
<6>NET: Registered protocol family 16
<6>hw-breakpoint: debug architecture 0x4 unsupported.
<6>Init eGon pin module V2.0
SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
<6>Initialize DMAC OK
<6>bio: create slab at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
<6>Switching to clocksource aw_64bits_counter
<5>FS-Cache: Loaded
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>CacheFiles: Loaded
[usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[sw_hcd0]: usb host driver initialize........
[sw_hcd0]: open_usb_clock
[sw_hcd0]: host_init_state = 1
[sw_hcd0]: platform is usb host
[sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
wrn: hcd is not enable, need not start hcd
[sw_hcd0]: sw_usb_host0_disable start
-------sw_hcd0_soft_disconnect---------
is_on = 0, hcd0_set_vbus_cnt = 0
[sw_hcd_host0]: Set USB Power Off
wrn: hcd is not enable, need not stop hcd
[sw_hcd0]: close_usb_clock
[sw_hcd0]: sw_usb_host0_disable end
[sw_udc]: udc_init: version 20080411
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP: reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.349:1): initialized
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.18)
<6>msgmni has been set to 675
<3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>sunxi disp driver loaded (/dev/disp api 1.0)
<6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
<6>[uart]: used uart info.: 0x11
<6>[uart]: serial probe 0 irq 1 mapbase 0x01c28000
<6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.4.67+ (root@debian) (gcc version 4.7.1 (Debian 4.7.1-7) ) #4 PREEMPT Sat Dec 14 15:12:10 EET 2013
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun4i
[ 0.000000] Memory cut off:
[ 0.000000] MALI : 0x5c000000 - 0x5fffffff ( 64 MB)
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory Reserved:
[ 0.000000] SYS : 0x43000000 - 0x4300ffff ( 64 kB)
[ 0.000000] VE : 0x44000000 - 0x48ffffff ( 80 MB)
[ 0.000000] LCD : 0x5a000000 - 0x5affffff ( 16 MB)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] sunxi: Allwinner A10 revision C (AW1623/sun4i) detected.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
[ 0.000000] Kernel command line: console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1280x720p50 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_res
erve=16 root=/dev/mmcblk0p2 rootwait panic=10
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 346060k/346060k available, 112692k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff000000 ( 552 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07b67b8 (7866 kB)
[ 0.000000] .init : 0xc07b7000 - 0xc07e2000 ( 172 kB)
[ 0.000000] .data : 0xc07e2000 - 0xc084fd28 ( 440 kB)
[ 0.000000] .bss : 0xc084fd4c - 0xc0a0c0a8 (1777 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.005998] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
[ 0.050262] pid_max: default: 32768 minimum: 301
[ 0.053848] Mount-cache hash table entries: 512
[ 0.057702] Initializing cgroup subsys cpuacct
[ 0.061107] Initializing cgroup subsys devices
[ 0.064503] Initializing cgroup subsys freezer
[ 0.067745] Initializing cgroup subsys blkio
[ 0.071296] CPU: Testing write buffer coherency: ok
[ 0.078854] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 0.084404] Setting up static identity map for 0x40555480 - 0x405554d8
[ 0.087264] devtmpfs: initialized
[ 0.089544] dummy:
[ 0.093059] NET: Registered protocol family 16
[ 0.098487] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.101925] Init eGon pin module V2.0
[ 0.107336] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[ 0.109426] Initialize DMAC OK
[ 0.116555] bio: create slab at 0
[ 0.119787] SCSI subsystem initialized
[ 0.127313] usbcore: registered new interface driver usbfs
[ 0.131673] usbcore: registered new interface driver hub
[ 0.135757] usbcore: registered new device driver usb
[ 0.139443] Linux video capture interface: v2.00
[ 0.144926] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.147790] Bluetooth: Core ver 2.16
[ 0.151217] NET: Registered protocol family 31
[ 0.156520] Bluetooth: HCI device and connection manager initialized
[ 0.160373] Bluetooth: HCI socket layer initialized
[ 0.164376] Bluetooth: L2CAP socket layer initialized
[ 0.168227] Bluetooth: SCO socket layer initialized
[ 0.172894] Switching to clocksource aw_64bits_counter
[ 0.174853] FS-Cache: Loaded
[ 0.180251] cfg80211: Calling CRDA to update world regulatory domain
[ 0.182396] CacheFiles: Loaded
[ 0.189267] [usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[ 0.193086] [sw_hcd0]: usb host driver initialize........
[ 0.197283] [sw_hcd0]: open_usb_clock
[ 0.221458] [sw_hcd0]: host_init_state = 1
[ 0.222427] [sw_hcd0]: platform is usb host
[ 0.225347] [sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[ 0.236521] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 38
[ 0.249055] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[ 0.255752] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[ 0.258947] hub 1-0:1.0: USB hub found
[ 0.261835] hub 1-0:1.0: 1 port detected
[ 0.265682] wrn: hcd is not enable, need not start hcd
[ 0.266933] [sw_hcd0]: sw_usb_host0_disable start
[ 0.272945] -------sw_hcd0_soft_disconnect---------
[ 0.275910] is_on = 0, hcd0_set_vbus_cnt = 0
[ 0.278958] [sw_hcd_host0]: Set USB Power Off
[ 0.282702] wrn: hcd is not enable, need not stop hcd
[ 0.283716] [sw_hcd0]: close_usb_clock
[ 0.286213] [sw_hcd0]: sw_usb_host0_disable end
[ 0.289383] [sw_udc]: udc_init: version 20080411
[ 0.295573] NET: Registered protocol family 2
[ 0.301683] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.308159] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.313886] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.319503] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.321688] TCP: reno registered
[ 0.326474] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.331716] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.335187] NET: Registered protocol family 1
[ 0.340329] RPC: Registered named UNIX socket transport module.
[ 0.343991] RPC: Registered udp transport module.
[ 0.347695] RPC: Registered tcp transport module.
[ 0.353084] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.358188] audit: initializing netlink socket (disabled)
[ 0.361880] type=2000 audit(0.349:1): initialized
[ 0.370354] VFS: Disk quotas dquot_6.5.2
[ 0.375730] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.381368] NFS: Registering the id_resolver key type
[ 0.385506] NTFS driver 2.1.30 [Flags: R/W].
[ 0.388857] fuse init (API version 7.18)
[ 0.392097] msgmni has been set to 675
[ 0.401862] alg: comp: Compression test 1 failed for lzo-generic: output len = 57
[ 0.405017] alg: No test for stdrng (krng)
[ 0.411670] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.414554] io scheduler noop registered
[ 0.417852] io scheduler deadline registered
[ 0.421533] io scheduler cfq registered (default)
[ 0.426153] sunxi disp driver loaded (/dev/disp api 1.0)
[ 0.431664] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.435738] [uart]: used uart info.: 0x11
[ 0.440364] [uart]: serial probe 0 irq 1 mapbase 0x01c28000
[ 0.466364] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
<6>console [ttyS0] enabled
[ 1.127584] console [ttyS0] enabled
<6>[uart]: serial probe 4 irq 17 mapbase 0x01c29000
[ 1.135864] [uart]: serial probe 4 irq 17 mapbase 0x01c29000
<6>sunxi-uart.4: ttyS1 at MMIO 0x1c29000 (irq = 17) is a U6_16550A
[ 1.167546] sunxi-uart.4: ttyS1 at MMIO 0x1c29000 (irq = 17) is a U6_16550A
<7>G2D: drv_g2d_init
<6>G2D: Module initialized.major:251
[ 1.180231] G2D: Module initialized.major:251
<6>brd: module loaded
[ 1.187201] brd: module loaded
<6>loop: module loaded
[ 1.194291] loop: module loaded
[NAND] nand driver version: 0x2 0x9
[ 1.200813] [NAND] nand driver version: 0x2 0x9
[SCAN_ERR] search nand physical architecture parameter failed!
[ 1.211038] [SCAN_ERR] search nand physical architecture parameter failed!
[NAND]init_blklayer fail
[ 1.220270] [NAND]init_blklayer fail
<6>sunxi_emac Using mii phy on PortA
[ 1.227432] sunxi_emac Using mii phy on PortA
<6>sunxi_emac Using MAC from SID: 02:4f:02:02:25:dd[ 1.246371] sunxi_emac Using MAC from SID: 02:4f:02:02:25:dd<6>ehci_hcd: USB 2.0 'Enhanced' Host C
ontroller (EHCI) Driver
[ 1.259155] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.271047] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[sw-ehci1]: open clock
[ 1.279509] [sw-ehci1]: open clock
[sw-ehci1]: Set USB Power ON
[ 1.305482] [sw-ehci1]: Set USB Power ON
<6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.315846] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[ 1.329346] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
<6>sw-ehci sw-ehci.1: irq 39, io mem 0x01c14000
[ 1.340738] sw-ehci sw-ehci.1: irq 39, io mem 0x01c14000
<6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
[ 1.367291] sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
<6>hub 2-0:1.0: USB hub found
[ 1.375891] hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
[ 1.382521] hub 2-0:1.0: 1 port detected
[sw-ohci1]: open clock
[ 1.388890] [sw-ohci1]: open clock
<6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.418326] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[ 1.431475] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
<6>sw-ohci sw-ohci.1: irq 64, io mem 0x01c14400
[ 1.442811] sw-ohci sw-ohci.1: irq 64, io mem 0x01c14400
<6>hub 3-0:1.0: USB hub found
[ 1.510002] hub 3-0:1.0: USB hub found
<6>hub 3-0:1.0: 1 port detected
[ 1.516663] hub 3-0:1.0: 1 port detected
[sw-ehci2]: open clock
[ 1.522986] [sw-ehci2]: open clock
[sw-ehci2]: Set USB Power ON
[ 1.548962] [sw-ehci2]: Set USB Power ON
<6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.559305] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
<6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[ 1.572798] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
<6>sw-ehci sw-ehci.2: irq 40, io mem 0x01c1c000
[ 1.584177] sw-ehci sw-ehci.2: irq 40, io mem 0x01c1c000
<6>sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00
[ 1.607280] sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00
<6>hub 4-0:1.0: USB hub found
[ 1.615823] hub 4-0:1.0: USB hub found
<6>hub 4-0:1.0: 1 port detected
[ 1.622472] hub 4-0:1.0: 1 port detected
[sw-ohci2]: open clock
[ 1.628785] [sw-ohci2]: open clock
<6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.658216] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
<6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[ 1.671365] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
<6>sw-ohci sw-ohci.2: irq 65, io mem 0x01c1c400
[ 1.682698] sw-ohci sw-ohci.2: irq 65, io mem 0x01c1c400
<6>hub 5-0:1.0: USB hub found
[ 1.749947] hub 5-0:1.0: USB hub found
<6>hub 5-0:1.0: 1 port detected
[ 1.756600] hub 5-0:1.0: 1 port detected
<6>Initializing USB Mass Storage driver...
[ 1.764553] Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
[ 1.774541] usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
[ 1.784125] USB Mass Storage support registered.
<6>usbcore: registered new interface driver ums-alauda
[ 1.793651] usbcore: registered new interface driver ums-alauda
<6>usbcore: registered new interface driver ums-cypress
[ 1.804561] usbcore: registered new interface driver ums-cypress
<6>usbcore: registered new interface driver ums-datafab
[ 1.815554] usbcore: registered new interface driver ums-datafab
<6>usbcore: registered new interface driver ums_eneub6250
[ 1.826718] usbcore: registered new interface driver ums_eneub6250
<6>usbcore: registered new interface driver ums-freecom
[ 1.837890] usbcore: registered new interface driver ums-freecom
<6>usbcore: registered new interface driver ums-isd200
[ 1.848794] usbcore: registered new interface driver ums-isd200
<6>usbcore: registered new interface driver ums-jumpshot
[ 1.859833] usbcore: registered new interface driver ums-jumpshot
<6>usbcore: registered new interface driver ums-karma
[ 1.870742] usbcore: registered new interface driver ums-karma
<6>usbcore: registered new interface driver ums-onetouch
[ 1.881656] usbcore: registered new interface driver ums-onetouch
<6>usbcore: registered new interface driver ums-realtek
[ 1.892746] usbcore: registered new interface driver ums-realtek
<6>usbcore: registered new interface driver ums-sddr09
[ 1.903653] usbcore: registered new interface driver ums-sddr09
<6>usbcore: registered new interface driver ums-sddr55
[ 1.914474] usbcore: registered new interface driver ums-sddr55
<6>usbcore: registered new interface driver ums-usbat
[ 1.925206] usbcore: registered new interface driver ums-usbat
<6>mousedev: PS/2 mouse device common for all mice
[ 1.935688] mousedev: PS/2 mouse device common for all mice
sun4i-ts.c: sun4i_ts_init: start ...
[ 1.944811] sun4i-ts.c: sun4i_ts_init: start ...
rtp_used == 1.
[ 1.950958] rtp_used == 1.
sun4i-ts: tp_screen_size is 5 inch.
[ 1.956986] sun4i-ts: tp_screen_size is 5 inch.
sun4i-ts: tp_regidity_level is 5.
[ 1.964553] sun4i-ts: tp_regidity_level is 5.
sun4i-ts: tp_press_threshold_enable is 0.
[ 1.972655] sun4i-ts: tp_press_threshold_enable is 0.
sun4i-ts: rtp_sensitive_level is 15.
[ 1.981017] sun4i-ts: rtp_sensitive_level is 15.
sun4i-ts: rtp_exchange_x_y_flag is 0.
[ 1.989034] sun4i-ts: rtp_exchange_x_y_flag is 0.
sun4i-ts.c: sun4i_ts_probe: start...
[ 1.997153] sun4i-ts.c: sun4i_ts_probe: start...
begin get platform resourec
[ 2.004294] begin get platform resourec
<6>input: sun4i-ts as /devices/platform/sun4i-ts/input/input0
[ 2.013767] input: sun4i-ts as /devices/platform/sun4i-ts/input/input0
tp init
[ 2.021230] tp init
sun4i-ts.c: sun4i_ts_probe: end
[ 2.026219] sun4i-ts.c: sun4i_ts_probe: end
<6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[ 2.035851] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
<6>i2c /dev entries driver
[ 2.044433] i2c /dev entries driver
config i2c gpio with gpio_config api
[ 2.051585] config i2c gpio with gpio_config api
<6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[ 2.061813] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
<6>I2C: i2c-0: AW16XX I2C adapter
[ 2.070713] I2C: i2c-0: AW16XX I2C adapter
<6>I2C: i2c-1: AW16XX I2C adapter
[ 2.078113] I2C: i2c-1: AW16XX I2C adapter
<6>I2C: i2c-2: AW16XX I2C adapter
[ 2.085446] I2C: i2c-2: AW16XX I2C adapter
<6>lirc_dev: IR Remote Control driver registered, major 250
[ 2.095048] lirc_dev: IR Remote Control driver registered, major 250
<6>IR NEC protocol handler initialized
[ 2.104977] IR NEC protocol handler initialized
<6>IR RC5(x) protocol handler initialized
[ 2.113253] IR RC5(x) protocol handler initialized
<6>IR RC6 protocol handler initialized
[ 2.121527] IR RC6 protocol handler initialized
<6>IR JVC protocol handler initialized
[ 2.129540] IR JVC protocol handler initialized
<6>IR Sony protocol handler initialized
[ 2.137640] IR Sony protocol handler initialized
<6>IR RC5 (streamzap) protocol handler initialized
[ 2.146766] IR RC5 (streamzap) protocol handler initialized
<6>IR SANYO protocol handler initialized
[ 2.155994] IR SANYO protocol handler initialized
<6>IR MCE Keyboard/mouse protocol handler initialized
[ 2.165480] IR MCE Keyboard/mouse protocol handler initialized
<6>IR LIRC bridge handler initialized
[ 2.174707] IR LIRC bridge handler initialized
<6>usbcore: registered new interface driver uvcvideo
[ 2.183938] usbcore: registered new interface driver uvcvideo
<6>USB Video Class driver (1.1.1)
[ 2.192736] USB Video Class driver (1.1.1)
[ace_drv] start!!!
[ 2.198615] [ace_drv] start!!!
[ace_drv] init end!!!
[ 2.203925] [ace_drv] init end!!!
[pa_drv] start!!!
[ 2.208919] [pa_drv] start!!!
[pa_drv] init end!!!
[ 2.214006] [pa_drv] init end!!!
<6>axp20_ldo1: 1300 mV
[ 2.219529] axp20_ldo1: 1300 mV
<6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[ 2.227908] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
<6>axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[ 2.238021] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
<6>axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[ 2.248315] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
<6>axp20_buck2: 700 <--> 2275 mV at 1400 mV
[ 2.258493] axp20_buck2: 700 <--> 2275 mV at 1400 mV
<6>axp20_buck3: 700 <--> 3500 mV at 1250 mV
[ 2.268675] axp20_buck3: 700 <--> 3500 mV at 1250 mV
<6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[ 2.278567] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
<6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input1
[ 2.293253] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input1
<4>axp20_ldo2: Failed to create debugfs directory
[ 2.322101] axp20_ldo2: Failed to create debugfs directory
<6>Bluetooth: HCI UART driver ver 2.2
[ 2.331523] Bluetooth: HCI UART driver ver 2.2
<6>Bluetooth: HCI H4 protocol initialized
[ 2.339719] Bluetooth: HCI H4 protocol initialized
<6>Bluetooth: HCI BCSP protocol initialized
[ 2.348431] Bluetooth: HCI BCSP protocol initialized
<6>Bluetooth: HCILL protocol initialized
[ 2.357051] Bluetooth: HCILL protocol initialized
<6>cpuidle: using governor ladder
[ 2.364796] cpuidle: using governor ladder
<6>cpuidle: using governor menu
[ 2.371769] cpuidle: using governor menu
[mmc_pm]: no sdio card used in configuration
[ 2.379734] [mmc_pm]: no sdio card used in configuration
[mmc]: sunximmc_init
[ 2.386974] [mmc]: sunximmc_init
[mmc]: sunxi mmc controller using config : 0x9
[ 2.394488] [mmc]: sunxi mmc controller using config : 0x9
[mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[ 2.404885] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[mmc]: mmc 0 power off !!
[ 2.413664] [mmc]: mmc 0 power off !!
[mmc]: mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xdba28000, ret 0.
[ 2.424851] [mmc]: mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xdba28000, ret 0.
[mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[ 2.437446] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[mmc]: mmc 3 power off !!
[ 2.446190] [mmc]: mmc 3 power off !!
[mmc]: mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xdba30000, ret 0.
[ 2.457243] [mmc]: mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xdba30000, ret 0.
<6>sunxi_leds driver init
[ 2.467292] sunxi_leds driver init
<6>sunxi leds can't find script data '[leds_para]' 'leds_used'
[ 2.476249] sunxi leds can't find script data '[leds_para]' 'leds_used'
<6>usbcore: registered new interface driver usbhid
[ 2.487860] usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
[ 2.496230] usbhid: USB HID core driver
<6>logger: created 256K log 'log_main'
[ 2.503864] logger: created 256K log 'log_main'
<6>logger: created 256K log 'log_events'
[ 2.512170] logger: created 256K log 'log_events'
<6>logger: created 256K log 'log_radio'
[ 2.520533] logger: created 256K log 'log_radio'
<6>logger: created 256K log 'log_system'
[ 2.528893] logger: created 256K log 'log_system'
[I2S]sunxi-i2s cannot find any using configuration for controllers, return directly!
[ 2.542521] [I2S]sunxi-i2s cannot find any using configuration for controllers, return directly!
[I2S]sndi2s cannot find any using configuration for controllers, return directly!
[ 2.558717] [I2S]sndi2s cannot find any using configuration for controllers, return directly!
<6>IPv4 over IPv4 tunneling driver
[ 2.570630] IPv4 over IPv4 tunneling driver
<6>TCP: cubic registered
[ 2.577549] TCP: cubic registered
<6>Initializing XFRM netlink socket
[ 2.584079] Initializing XFRM netlink socket
<6>NET: Registered protocol family 17
[ 2.591790] NET: Registered protocol family 17
<6>NET: Registered protocol family 15
[ 2.599666] NET: Registered protocol family 15
<6>Bluetooth: RFCOMM TTY layer initialized
[ 2.608109] Bluetooth: RFCOMM TTY layer initialized
<6>Bluetooth: RFCOMM socket layer initialized
[ 2.617154] Bluetooth: RFCOMM socket layer initialized
<6>Bluetooth: RFCOMM ver 1.11
[ 2.624981] Bluetooth: RFCOMM ver 1.11
<6>Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.633006] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>Bluetooth: BNEP filters: protocol multicast
[ 2.642496] Bluetooth: BNEP filters: protocol multicast
<6>8021q: 802.1Q VLAN Support v1.8
[ 2.650899] 8021q: 802.1Q VLAN Support v1.8
[mmc_pm]: No sdio card, please check your config !!
[ 2.659714] [mmc_pm]: No sdio card, please check your config !!
<5>Registering the dns_resolver key type
[ 2.669306] Registering the dns_resolver key type
<6>VFP support v0.3: [ 2.676027] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
implementor 41 architecture 3 part 30 variant c rev 3
<5>Registering SWP/SWPB emulation handler
[ 2.692238] Registering SWP/SWPB emulation handler
<4>axp20_buck2: Failed to create debugfs directory
[ 2.701581] axp20_buck2: Failed to create debugfs directory
<6>registered taskstats version 1
[ 2.710987] registered taskstats version 1
<6>I2C: i2c-3: HDMI I2C adapter
[ 2.806738] I2C: i2c-3: HDMI I2C adapter
<6>disp clks: lcd 74250000 pre_scale 1 hdmi 74250000 pll 297000000 2x 0
[ 2.839387] disp clks: lcd 74250000 pre_scale 1 hdmi 74250000 pll 297000000 2x 0
[mmc]: mmc 0 detect change, present 1
[ 3.416306] [mmc]: mmc 0 detect change, present 1
<6>Console: switching to colour frame buffer device 160x45
[ 3.531065] Console: switching to colour frame buffer device 160x45
<4>axp20_buck3: incomplete constraints, leaving on
[ 3.588259] axp20_buck3: incomplete constraints, leaving on
<4>axp20_buck2: incomplete constraints, leaving on
[ 3.607655] axp20_buck2: incomplete constraints, leaving on
<4>axp20_ldo4: incomplete constraints, leaving on
[ 3.627567] axp20_ldo4: incomplete constraints, leaving on
<4>axp20_ldo3: incomplete constraints, leaving on
[ 3.647564] axp20_ldo3: incomplete constraints, leaving on
<4>axp20_ldo2: incomplete constraints, leaving on
[ 3.660163] axp20_ldo2: incomplete constraints, leaving on
<4>axp20_ldo1: incomplete constraints, leaving on
[ 3.670335] axp20_ldo1: incomplete constraints, leaving on
<6>sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:16:09 UTC (1262304969)
[ 3.683470] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:16:09 UTC (1262304969)
<6>ALSA device list:
[ 3.693995] ALSA device list:
<6> #0: sunxi-CODEC Audio Codec
[ 3.700021] #0: sunxi-CODEC Audio Codec
<6>Waiting for root device /dev/mmcblk0p2...
[ 3.708514] Waiting for root device /dev/mmcblk0p2...
[mmc]: mmc 0 power on !!
[ 3.715908] [mmc]: mmc 0 power on !!
[mmc]: sdxc_request_done(L1118): [ 3.756568] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 52, RTO !!
smc 0 err, cmd 52, RTO !!
[mmc]: sdxc_request_done(L1118): [ 3.769308] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 52, RTO !!
smc 0 err, cmd 52, RTO !!
[mmc]: sdxc_request_done(L1118): [ 3.785694] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 5, RTO !!
smc 0 err, cmd 5, RTO !!
[mmc]: sdxc_request_done(L1118): [ 3.798251] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 5, RTO !!
smc 0 err, cmd 5, RTO !!
[mmc]: sdxc_request_done(L1118): [ 3.810808] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 5, RTO !!
smc 0 err, cmd 5, RTO !!
[mmc]: sdxc_request_done(L1118): [ 3.823360] [mmc]: sdxc_request_done(L1118): smc 0 err, cmd 5, RTO !!
smc 0 err, cmd 5, RTO !!
<6>mmc0: new high speed SDHC card at address aaaa
[ 3.872568] mmc0: new high speed SDHC card at address aaaa
<6>mmcblk0: mmc0:aaaa SU08G 7.40 GiB
[ 3.881773] mmcblk0: mmc0:aaaa SU08G 7.40 GiB
<6> mmcblk0: p1 p2
[ 3.889557] mmcblk0: p1 p2
<6>kjournald starting. Commit interval 5 seconds
[ 3.941589] kjournald starting. Commit interval 5 seconds
<6>EXT3-fs (mmcblk0p2): using internal journal
[ 3.951356] EXT3-fs (mmcblk0p2): using internal journal
<6>EXT3-fs (mmcblk0p2): recovery complete
[ 3.960375] EXT3-fs (mmcblk0p2): recovery complete
<6>EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 3.970992] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
<6>VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 3.982866] VFS: Mounted root (ext3 filesystem) on device 179:2.
<6>devtmpfs: mounted
[ 3.992625] devtmpfs: mounted
<6>Freeing init memory: 172K
[ 3.998499] Freeing init memory: 172K
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd<30>udevd[164]: starting version 175
[ 4.912803] udevd[164]: starting version 175
udevd[164]: specified group 'videO' unknown
. ok
udevd[164]: specified group 'videO' unknown
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
Starting fake hwclock: loading system time.
Thu Jan 9 13:50:02 UTC 2014
[ ok ] Activating swap...done.
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/mmcblk0p2: clean, 52217/193920 files, 306791/786432 blocks
done.
<6>EXT3-fs (mmcblk0p2): using internal journal
[ 7.227987] EXT3-fs (mmcblk0p2): using internal journal
[ ok ] Cleaning up temporary files... /tmp.
[info] Loading kernel module sw_ahci_platform.
<6>sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
[ 7.560535] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
<4>sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[ 7.580035] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
<6>sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 7.592877] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
<6>sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
[ 7.607775] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
<6>scsi0 : sw_ahci_platform
[ 7.622444] scsi0 : sw_ahci_platform
<6>ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 56
[ 7.635948] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 56
<6>ata1: SATA link down (SStatus 0 SControl 300)
[ 7.997254] ata1: SATA link down (SStatus 0 SControl 300)
[info] Loading kernel module lcd.
[info] Loading kernel module hdmi.
[info] Loading kernel module ump.
UMP<2>: [ 8.174301] UMP<2>: Inserting UMP device driver. Compiled: Dec 12 2013, time: 14:54:06
Inserting UMP device driver. Compiled: Dec 12 2013, time: 14:54:06
UMP<2>: [ 8.191723] UMP<2>: Using OS memory backend, allocation limit: 134217728
Using OS memory backend, allocation limit: 134217728
UMP: [ 8.203722] UMP: UMP device driver loaded
UMP device driver loaded
[info] Loading kernel module disp.
[info] Loading kernel module 8192cu.
ERR: script_parser_fetch usb_controller_type failed
[ 9.049073] ERR: script_parser_fetch usb_controller_type failed
<6>usbcore: registered new interface driver rtl8192cu
[ 9.062001] usbcore: registered new interface driver rtl8192cu
[info] Loading kernel module gpio-sunxi.
<6>sunxi_gpio driver init ver 1.3
[ 9.171898] sunxi_gpio driver init ver 1.3
<3>sunxi_gpio_probe script_parser_fetch '[gpio_para]' 'gpio_pin_76' err
[ 9.190419] sunxi_gpio_probe script_parser_fetch '[gpio_para]' 'gpio_pin_76' err
<6>gpiochip_add: registered GPIOs 1 to 81 on device: A1X_GPIO
[ 9.209244] gpiochip_add: registered GPIOs 1 to 81 on device: A1X_GPIO
[info] Loading kernel module sunxi_cedar_mod.
[cedar dev]: install start!!!
[ 9.288380] [cedar dev]: install start!!!
[cedar dev]: install end!!!
[ 9.302672] [cedar dev]: install end!!!
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ ok ] Configuring network interfaces...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting up ALSA...done.
[ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix.
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting enhanced syslogd: rsyslogd.
Starting X display manager: slim.
[warn] /etc/environment has been deprecated for locale information; use /etc/default/locale for LC_ALL="en_US.utf8" instead ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[....] Starting system message bus: dbus<4>Warning: this sunxi disp driver will see significant redesign.
[ 15.561644] Warning: this sunxi disp driver will see significant redesign.
<4>Applications using /dev/disp directly will break.
[ 15.574096] Applications using /dev/disp directly will break.
<4>For more information visit: http://linux-sunxi.org/Sunxi_disp_driver
[ 15.589382] For more information visit: http://linux-sunxi.org/Sunxi_disp_driver
<4>[DISP] layer allocated: 0,101
[ 15.602100] [DISP] layer allocated: 0,101
Mali: [ 15.765668] Mali: permit MALI_IOC_MEM_MAP_EXT ioctl for framebuffer (paddr=0x5A000000, size=16777216)
permit MALI_IOC_MEM_MAP_EXT ioctl for framebuffer (paddr=0x5A000000, size=16777216)
<6>mali: use config clk_div 4
[ 15.811525] mali: use config clk_div 4
<6>mali: clk_div 4
[ 15.822853] mali: clk_div 4
Mali: [ 15.830543] Mali: mali clock set completed, clock is 240000000 Hz
mali clock set completed, clock is 240000000 Hz
<6>mali: use config clk_div 4
[ 15.856740] mali: use config clk_div 4
<6>mali: clk_div 4
[ 15.862233] mali: clk_div 4
Mali: [ 15.874383] Mali: mali clock set completed, clock is 240000000 Hz
mali clock set completed, clock is 240000000 Hz
Mali: [ 15.900726] Mali: Mali device driver loaded
Mali device driver loaded
.
<6>[drm] Initialized drm 1.1.0 20060810.
[ 16.437141] [drm] Initialized drm 1.1.0 20060810
[ ok done (none).
<6>Mali DRM initialize, driver name: mali_drm, version 2.1
[ 16.493299] Mali DRM initialize, driver name: mali_drm, version 2.1
[....] CPUFreq Utilities: Setting performance CPUFreq governor...<6>[drm] Initialized mali_drm 2.1.1 20101111 on minor 0
[ 16.539517] [drm] Initialized mali_drm 2.1.1 20101111 on minor 0
CPU0...<6>Mali DRM initialize, driver name: mali_drm, version 2.1
[ 16.555248] Mali DRM initialize, driver name: mali_drm, version 2.1
<6>[drm] Initialized mali_drm 2.1.1 20101111 on minor 1
[ 16.570147] [drm] Initialized mali_drm 2.1.1 20101111 on minor 1
UMP<2>: [ 16.581256] UMP<2>: New session opened
New session opened
done.
[ ok ] Starting network connection manager: NetworkManager.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
Debian GNU/Linux 7.0 a10Lime ttyS0
a10Lime login: root (automatic login)
Last login: Thu Jan 9 13:50:52 UTC 2014 on ttyS0
Linux a10Lime 3.4.67+ #4 PREEMPT Sat Dec 14 15:12:10 EET 2013 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~# ls
change_display_a10_lime.sh Desktop
root@a10Lime:~# dir
change_display_a10_lime.sh Desktop
root@a10Lime:~# ls -la
total 264
drwx------ 16 root root 4096 Jan 9 13:48 .
drwxr-xr-x 26 root root 4096 Dec 18 14:13 ..
drwx------ 2 root root 4096 Jan 2 19:00 .aptitude
-rw------- 1 root root 9 Jan 9 13:50 .bash_history
-rw-r--r-- 1 root root 220 Jan 1 2013 .bash_logout
-rw-r--r-- 1 root root 3429 Jan 1 2010 .bashrc
drwxr-xr-x 6 root root 4096 Dec 18 13:37 .cache
-rwxr-xr-x 1 root root 30979 Jan 9 13:12 change_display_a10_lime.sh
drwxr-xr-x 12 root root 4096 Dec 18 19:08 .config
drwx------ 3 root root 4096 Nov 19 06:16 .dbus
drwxr-xr-x 2 root root 4096 Nov 19 06:16 Desktop
-rw-r--r-- 1 root root 35 Jan 1 2010 .dmrc
drwx------ 3 root root 4096 Dec 18 19:17 .gconf
-rw-r--r-- 1 root root 26 Nov 18 14:03 .gitconfig
drwxr-xr-x 2 root root 4096 Dec 11 06:56 .gstreamer-0.10
drwx------ 2 root root 4096 Nov 19 06:16 .gvfs
drwx------ 3 root root 4096 Nov 19 09:21 .local
drwxr-xr-x 2 root root 4096 Nov 18 08:58 .mplayer
-rw------- 1 root root 178 Jan 9 13:48 .nano_history
-rw-r--r-- 1 root root 675 Jan 1 2013 .profile
drwx------ 2 root root 4096 Dec 18 19:19 .pulse
-rw------- 1 root root 256 Nov 18 08:58 .pulse-cookie
drwx------ 2 root root 4096 Nov 18 06:38 .ssh
drwx------ 2 root root 4096 Nov 19 12:37 .synaptic
drwx------ 4 root root 4096 Nov 19 09:18 .thumbnails
-rw------- 1 root root 103 Dec 18 19:14 .Xauthority
-rw------- 2 root root 0 Dec 18 19:27 .Xauthority-c
-rw------- 2 root root 0 Dec 18 19:27 .Xauthority-l
-rw------- 1 root root 102406 Dec 18 19:27 .xsession-errors
-rw------- 1 root root 20618 Jan 1 2010 .xsession-errors.old
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~# <6>ParseEDID
[ 33.453161] ParseEDID
<6>EDID version: 1.3
[ 33.490179] EDID version: 1.3
<6>PCLK=148500000 X 1920 2008 2052 2200 Y 1080 1084 1089 1125 fr 60 PP
[ 33.499637] PCLK=148500000 X 1920 2008 2052 2200 Y 1080 1084 1089 1125 fr 60 PP
<6>Using above mode as preferred EDID mode
[ 33.510991] Using above mode as preferred EDID mode
<4>Unimplemented SVD code 31
<4>Unimplemented SVD code 16
<4>disp_clk: Could not find a matching pll-freq for 53900000 pclk
<4>disp_clk: Could not find a matching pll-freq for 53900000 pclk
<4>disp_clk: Could not find a matching pll-freq for 108100000 pclk
<4>disp_clk: Could not find a matching pll-freq for 72650000 pclk
<4>disp_clk: Could not find a matching pll-freq for 74200000 pclk
<4>disp_clk: Could not find a matching pll-freq for 25150000 pclk
<4>disp_clk: Could not find a matching pll-freq for 146850000 pclk
<4>disp_clk: Could not find a matching pll-freq for 78800000 pclk
<4>disp_clk: Could not find a matching pll-freq for 26150000 pclk
[ 33.615592] Unimplemented SVD code 31
[ 33.618207] Unimplemented SVD code 16
[ 33.624052] disp_clk: Could not find a matching pll-freq for 53900000 pclk
[ 33.630039] disp_clk: Could not find a matching pll-freq for 53900000 pclk
[ 33.635958] disp_clk: Could not find a matching pll-freq for 108100000 pclk
[ 33.641808] disp_clk: Could not find a matching pll-freq for 72650000 pclk
[ 33.647632] disp_clk: Could not find a matching pll-freq for 74200000 pclk
[ 33.653476] disp_clk: Could not find a matching pll-freq for 25150000 pclk
[ 33.659408] disp_clk: Could not find a matching pll-freq for 146850000 pclk
[ 33.665233] disp_clk: Could not find a matching pll-freq for 78800000 pclk
[ 33.671075] disp_clk: Could not find a matching pll-freq for 26150000 pclk
<6>Parse_VideoData_Block: VIC 16 (native) support
[ 33.745147] Parse_VideoData_Block: VIC 16 (native) support
<6>Parse_VideoData_Block: VIC 4 support
[ 33.755117] Parse_VideoData_Block: VIC 4 support
<6>Parse_VideoData_Block: VIC 3 support
[ 33.763561] Parse_VideoData_Block: VIC 3 support
<6>Parse_VideoData_Block: VIC 1 support
[ 33.771953] Parse_VideoData_Block: VIC 1 support
<6>Parse_VideoData_Block: VIC 20 support
[ 33.780403] Parse_VideoData_Block: VIC 20 support
<6>Parse_VideoData_Block: VIC 18 support
[ 33.788926] Parse_VideoData_Block: VIC 18 support
<6>Parse_VideoData_Block: VIC 5 support
[ 33.797374] Parse_VideoData_Block: VIC 5 support
<6>Parse_VideoData_Block: VIC 31 support
[ 33.806358] Parse_VideoData_Block: VIC 31 support
<6>Parse_VideoData_Block: VIC 16 support
[ 33.814719] Parse_VideoData_Block: VIC 16 support
<6>Parse_VideoData_Block: VIC 19 support
[ 33.823344] Parse_VideoData_Block: VIC 19 support
<6>Parse_AudioData_Block: max channel=2
[ 33.831905] Parse_AudioData_Block: max channel=2
<6>Parse_AudioData_Block: SampleRate code=7
[ 33.840632] Parse_AudioData_Block: SampleRate code=7
<6>Parse_AudioData_Block: WordLen code=7
[ 33.849437] Parse_AudioData_Block: WordLen code=7
<6>Find HDMI Vendor Specific DataBlock
[ 33.857985] Find HDMI Vendor Specific DataBlock
<6>PCLK=148500000 X 1920 2008 2052 2200 Y 1080 1084 1089 1125 fr 60 PP
[ 33.868973] PCLK=148500000 X 1920 2008 2052 2200 Y 1080 1084 1089 1125 fr 60 PP
<6>PCLK=74250000 X 1920 2008 2052 2200 Y 540 542 547 562 fr 60 PP
[ 33.882307] PCLK=74250000 X 1920 2008 2052 2200 Y 540 542 547 562 fr 60 PP
<6>PCLK=74250000 X 1280 1390 1430 1650 Y 720 725 730 750 fr 60 PP
[ 33.895192] PCLK=74250000 X 1280 1390 1430 1650 Y 720 725 730 750 fr 60 PP
<6>PCLK=27000000 X 720 736 798 858 Y 480 489 495 525 fr 59 NN
[ 33.907716] PCLK=27000000 X 720 736 798 858 Y 480 489 495 525 fr 59 NN
<6>asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[ 33.924943] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~#
root@a10Lime:~# ehci_irq: port change detect
[ 57.053848] ehci_irq: port change detect
ehci_irq: port change detect
[ 57.213247] ehci_irq: port change detect
The port change to OHCI now!
[ 57.273247] The port change to OHCI now!
<6>usb 3-1: new low-speed USB device number 2 using sw-ohci
[ 57.575899] usb 3-1: new low-speed USB device number 2 using sw-ohci
<6>input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/sw-ohci.1/usb3/3-1/3-1:1.0/input/input2
[ 57.786710] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/platform/sw-ohci.1/usb3/3-1/3-1:1.0/input/input2
<6>generic-usb 0003:045E:0040.0001: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-sw-ohci-1/input0
[ 57.812696] generic-usb 0003:045E:0040.0001: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-sw-ohci-1/inp
ut0
Broadcast message from root@a10Lime (Thu Jan 9 13:51:11 2014):
The system is going down for system halt NOW!
[info] Using makefile-style concurrent boot in runlevel 0.
Stopping fake hwclock: saving system time.
[ ok ] Stopping network connection manager: NetworkManager.
<4>[DISP] layer released: 0,101
[ 76.127135] [DISP] layer released: 0,101
UMP<2>: Session closed
[ 76.163448] UMP<2>: Session closed
[ ok ] Shutting down ALSA...done.
Stopping X display manager: slim.
[ ok ] Asking all remaining processes to terminate...done.
[ ok ] All processes ended within 1 seconds...done.
[ ok ] Stopping enhanced syslogd: rsyslogd.
[info] Saving the system clock.
[ ok ] Deconfiguring network interfaces...done.
<6>sunxi-rtc sunxi-rtc: actually set time to 2014-1-9 13:51:14
[ 78.813826] sunxi-rtc sunxi-rtc: actually set time to 2014-1-9 13:51:14
[info] Hardware Clock updated to Thu Jan 9 13:51:14 UTC 2014.
[ ok ] Unmounting temporary filesystems...done.
[ ok ] Deactivating swap...done.
[ ok ] Unmounting local filesystems...done.
[info] Will now halt.
llklll<6>[sw-ohci2]: shutdown start
[ 81.912874] [sw-ohci2]: shutdown start
[sw-ohci2]: close clock
[ 81.918821] [sw-ohci2]: close clock
<6>[sw-ohci2]: shutdown end
[ 81.924890] [sw-ohci2]: shutdown end
<6>[sw-ehci2]: shutdown start
[ 81.931174] [sw-ehci2]: shutdown start
[sw-ehci2]: Set USB Power OFF
[ 81.938197] [sw-ehci2]: Set USB Power OFF
[sw-ehci2]: close clock
[ 81.944407] [sw-ehci2]: close clock
<6>[sw-ehci2]: shutdown end
[ 81.950434] [sw-ehci2]: shutdown end
<6>[sw-ohci1]: shutdown start
[ 81.956747] [sw-ohci1]: shutdown start
[sw-ohci1]: close clock
[ 81.962701] [sw-ohci1]: close clock
<6>[sw-ohci1]: shutdown end
[ 81.968725] [sw-ohci1]: shutdown end
<6>[sw-ehci1]: shutdown start
[ 81.975018] [sw-ehci1]: shutdown start
[sw-ehci1]: Set USB Power OFF
[ 81.981761] [sw-ehci1]: Set USB Power OFF
[sw-ehci1]: close clock
[ 81.987957] [sw-ehci1]: close clock
<6>[sw-ehci1]: shutdown end
[ 81.994028] [sw-ehci1]: shutdown end
wrn: hcd is disable, need not shutdown
[ 82.001127] wrn: hcd is disable, need not shutdown
<0>Power down.
[ 82.007417] Power down.
[axp] send power-off command!
[ 82.014194] [axp] send power-off command!

|
